{"product_id":"bigtreetech-manta-m5p-v1-0-control-board-32bit-support-5-axis-tmc2209-tmc5160-drivers-compatible-with-cb1-cb2-cm4-hdmi5-pitft50-tft35-spi-display-to-running-klipper-for-ender-3-voron-v0-fdm-3d-printer-btt-manta-m5p","title":"BIGTREETECH Manta M5P V1.0 Control Board 32Bit Support 5 Axis TMC2209 TMC5160 Drivers Compatible with CB1\/CB2\/CM4 HDMI5 PITFT50 TFT35 SPI Display to Running Klipper for Ender 3\/Voron V0 FDM 3D Printer BTT Manta M5P","description":"\u003ch3\u003eBIGTREETECH Manta M5P V1.0 Control Board 32Bit Support 5 Axis TMC2209 TMC5160 Drivers Compatible with CB1\/CB2\/CM4 HDMI5 PITFT50 TFT35 SPI Display to Running Klipper for Ender 3\/Voron V0 FDM 3D Printer\u003c\/h3\u003e\n\u003cp id=\"b\"\u003eBIGTREETECH Manta M5P Control board Product Introduction:BIGTREETECH Manta M5P\nis a 32-bit motherboard developed by the 3D printing team of Shenzhen Big Tree\nTechnology Co.,Ltd. for Klipper running.It can run Klipper with a core\nboard,which greatly eliminates the mass wiring between the motherboard and\nRaspberry-Pi ,and also greatly saves space in the chassis.The BTB header sare\ndesigned on Manta M5P, so that customers can choose to use CM4 or other\nsolutions, thus solving the insane shortage of Raspberry-Pi CM4.Main\nFeatures1. 32bit 64MHz ARM Cortex-M0+ series STM32G0B1RET6 MCU.2. The\nthermistor circuit is protected to prevent MCU damage from shorted heated bed\nand heater cartridge connections.3. The CNC fan's voltage is selectable in\n24V, 12V, and 5V, no more need for external stepdown thus preventing board\ndamage from user error.4. Thermistor connection supports pull-up resistance\nvalue setting using jumpers, no more extra module needed for PT1000.5. MCU\nfirmware can be upgraded via an SD card, or use DFU via Klipper's make flash\ncommand.6. BTB connectors are adopted between the motherboard and core board,\nallowing the choice of other core board solutions in addition to CM4.7.\nIntegrated SPI and UART mode of TMC driver and DIAG pin, easily configurable\nwith jumpers.8. Support filament runout sensor, BLTouch, RGB, etc.9.\nReplaceable fuse for easy maintenance.10. Onboard proximity switch port,\nsupport NPN and PNP type selection, (24V, 12V, 5V) voltage selection.11.\nOnboard SPI interface for connecting acceleration sensor to enable Klipper's\ninput shaping.12. The new E-FUSE fuse is equipped, which can respond quickly,\nenhance self-protection ability, and greatly reduce the motherboard burnout\ncaused by short circuits or ignition.\u003c\/p\u003e \n\n\u003ch3\u003eProduct Features\u003c\/h3\u003e\n  \u003cul class=\"a\"\u003e\n         \u003cli\u003eMain Control Chip Upgraded: BIGTREETECH Manta M5P control board adopts 32bit ARMCortex-M0STM32G0B1RET6 chip, frequency of 64MHz, it can installation of the BIGTREETECH CB2\/CB1\/eMMc\/Raspberry-Pi CM4 to run the Linux systyem, running Klipper, when without CB1 or CM4, can Running Marlin.\u003c\/li\u003e\n         \u003cli\u003eAbundant Connectivity: BTT Manta M5P support USB2.0*3, LAN,DSC,CSI, SPI, HDMI0 and HDMI1 display (PITFT50 V2.1, HDMI5 V1.1, TFT35 SPI), SOC-Card, MCU-Card, Onboard CAN, Probe,RGB*2, SPI,EXP1+EXP2, MIN1-MIN4, 40Pin-GPIO (about CANBUS,Can be directly connected to EBB using Klipper's USB to CAN bus bridge function).\u003c\/li\u003e\n         \u003cli\u003eRich Expansion Ports: Support filament runout detection sensor, BLtouch, BIQU Microprobe, RGB Lights, automatic shutdown module, Onboard proximity switch and SPI(ADXL345) port ,support NPN and PNP type selection,(24V,12V,5V)voltage selection, for users use Klipper firmware to connect external acceleration sensor for acceleration compensation.\u003c\/li\u003e\n         \u003cli\u003eEasy operation: Thermistor can select the value of pull-up resistor through jumper to support PT1000 without external module Convenient for user to DIY and the MCU firmware can be upgraded through SD card, or updated through DFU through Klipper's makeflash command.\u003c\/li\u003e\n         \u003cli\u003ePower chip upgraded: The Power Chip adopts TPS5450-5A, the 5A output perfectly matches the power supply need of Raspberry-Pi, integrated SPI and UART mode of TMC driver and DIAG pin,easily configur able with jumpers, please follow the Github Manual instructions for details.\u003c\/li\u003e\n         \u003cli\u003eAfter-sales service: The firmware update and installation instructions for Manta M5P have been uploaded to bigtreetech Github. If you encounter any problems during use, please let us know as soon as possible and we will give you a satisfactory solution.\u003c\/li\u003e\n  \u003c\/ul\u003e","brand":"BIGTREETECH","offers":[{"title":"BTT Manta M5P","offer_id":48068469424279,"sku":"B0C1TYD86S","price":285.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0461\/8380\/9175\/files\/B0C1TYD86S.jpg?v=1785073325","url":"https:\/\/newnestshop.com\/products\/bigtreetech-manta-m5p-v1-0-control-board-32bit-support-5-axis-tmc2209-tmc5160-drivers-compatible-with-cb1-cb2-cm4-hdmi5-pitft50-tft35-spi-display-to-running-klipper-for-ender-3-voron-v0-fdm-3d-printer-btt-manta-m5p","provider":"NewNest Australia","version":"1.0","type":"link"}